MSA's 2013 SEMA Project: Black Rhino > Front Bumper, Rear Bumper, and Other things you might not catch.

There are a few subtle changes on this vehicle that people don't notice.  I thought they deserved some pointing out.

FRONT BUMPER
If you notice the original rendering, the front bumper is WAY lower than OE.  It was designed that way.  The theme of the truck is a mini-semi truck.  In order to do so, we had to have a larger front bumper/air dam.  To do this we had to succeed in doing 2 things - keeping the factory lines and lowering it approximately 4 inches.  With our time constraints, our best option was to purchase another front bumper, weld, and mold it in.  When completely deflated, the front bumper with air dam sits about an inch off the ground.  Perfection.


REAR DUALLY FENDERS
As described in a previous blog, the rear fenders were rendered to be flush with the wheels.  But this was also our tow vehicle that would haul a 24' enclosed trailer with a drift car and tools.  So, we wanted 10ply tires to ensure the truck could handle the load.  Nitto, our sponsor, had 1 tire that would fit the bill - The Terra Grappler at LT315/50R24, which equates to a 36.54" total diameter and approximately 12.5" in width.  Most people walked by not realizing the massive width of the fender, but it came out to be about a 4 day job to make sure both sides not only matched, but the lines were right.

SUICIDE DOORS
Most people didn't play with these, and of course, we aren't complaining.  At shows, vehicles really aren't meant for the general public to just play and handle as they wish.  But, when one of us were present, we definitely want to show the 3 weeks of love put into this.  The doors open and close just like factory from the inside or the outside.  The gaps between the doors and the body are right.  The added metal reinforcement prevents them from sagging.

BAG SETUP
The rear setup is heavily reinforced.  We used 1/4" and 1/2" steel because we knew that there was a possibility of a gooseneck setup in the future.  So we set it up that way, and with our 3800lb bags, we should be able to haul just about anything.  The parallel bars and other items on the truck assists in that setup, keeping the rear more rigid than it was from the factory.

SWITCHES and RUNNING BOARDS
The switches and the running boards weren't offered for my truck's specific model.  They could have been upgraded, but weren't purchased that way.  The running boards are from a Lariat which were disassembled and painted.  This truck is an XLT model.  It also had the AUX OE Switch option that we purchased separately.  These run the Grille lights, additional fog lamps, and the rear bumper lights.

FENDERS
We actually molded the front fenders.  We wanted a more smooth look, and the front fenders seem out of place with the line in it.  Since we did that, we had to modify the Bushwacker Extend-A-Fenders up front to account for the body line elimination.

PAINT
It was a common misconception that we wrapped the truck.  There are several companies that had the brushed steel look in a wrap, so at a quick glance, a lot of people made that assumption.  But no.  We didn't want the truck to be merely wrapped.  That showed no technical skill.  We had to take it a step further and we actually "scratched" the truck to give it the brushed look.  We accomplished this with 180 grit sandpaper, and red and gray scotchbrite pads.  Total process took about 8 hours.

MSA's 2013 SEMA Project: Black Rhino > Fab Work continued...Wheels Arrive.

After some tracking, the wheels arrived at our door steps on October 21. Any person that does bag setups know that one of the crucial pieces of a bag setup is the wheels and tires. Location of the bags, parallel bars, and other bag components depend on it. BUT with some SEMA builds, you don't always have that luxury. So we guesstimated. Well....we guesstimated ok. We weren't terribly far off, but it definitely created needed some reconfiguration.

First, our bags were off. The bags have 10" of lift and the rear mounts were way lower than the front. The rears would have to air up 4" before it would equal where the fronts completely deflated. So we used the torch to completely cut out our current top bag mounts and made them lower. This allowed us to have equal height adjustments for both the front and the rear.

Second, we had started to fiberglass and do body work on the Bushwackers. Our original plan was to use the rear Extend-a-fenders made for the F250 and modify them for our Dually fenders. After mounting the wheels and tires, we would have been left with about 1" of tire that stuck out beyond the fenders. That was a no go. The design calls for the rear fenders to be completely flush. Well, we can bring the wheels in or we would have to cut the bed. That would then conflict with our BedRug sponsorship. So, the rear fenders...trashed. We overnighted 2 rear dually fenders from Ford, then cut, trimmed, and molded into the existing ones. This allowed us to extended our fenders out to where we wanted it - flush with the wheels. Having only a few days left, this was definitely going to be a rush.

Lastly, our fittings leaked.  Every single joint and fitting leaked.  So we spent hours upon hours upon hours, looking and searching for the correct fittings to correct all the points in the system that was leaking. Sometimes a set back when it comes to airbags.  But it was another challenge that was overcome.

MSA's 2013 SEMA Project: Black Rhino > Suicide Doors to completion

This specific blog will be picture heavy. We photo documented most every step of the way, and I'm just going to throw it all together rather than you reading everything individually. The key steps we took here are: 

1) We built and heavily reinforced the hinge mounting locations. Once of my irritations is seeing a suicide door sag. So the cab was reinforced and the door skins were heavily reinforced, thus allowing the hinges to take the weight of the door without any sagging.

2) Another key part of the build is the latch and hinge setup. The door handles and latches (door skin and all) were swapped. We cut out approximately 1" of door skin from around the door handle cavity and cut the majority of the latch so that we could swap sides and keep it's factory shape.

3) The locks are now closer to the latch. If you look, the door lock for the front doors are close to the latch. In other words, the latch and the door locks are both on the rear part of the front doors. On the factory rears, the door lock is closer to the front of the door and the latch is at the rear of the door. Having suicide doors, we moved the latch to the front of the door, so the rear doors now have the lock and the latch on the front part of the door. To make sure they still worked together, we purchased new front door locks and modified them to work. It may be hard to visualize, but I hope that makes some sense.

The suicide doors was about a 3 week process. There was a lot of time aligning parts - making sure the door gaps were correct, the hinges were perfectly aligned, etc... But, it was all well worth it. The only issue we have now is that the rear doors and front doors cannot open at the same time. There is a sweet spot at the start of the opening of the doors, where the top corners overlap each other.

Enjoy:

MSA's 2013 SEMA Project: Black Rhino > Speaker Pods - Building the Rear Speaker Pods Step by step

The rear pods were built very much like the first. Except there was once step change.  Here's what we did.

Step 1: Trimmed and created a wooden structure what would work within the door panels.  We trimmed the door panels as well, where necessary.

Step 2: Created a base for the structure using wood this time rather than fiberglass.  The reason for this is that it's quicker because the wood didn't have to dry like resin does.  Also, it was a flat surface and had no contours.

Step 3: W reassembled the door panel and taped it with aluminum tape.  The floor, the sides, and everywhere we wanted to see the pod's form.  We then placed the wooden frame in its location.

Step 4: Here's what we tried....Great Stuff.  We got a few cans of "Great Stuff" at Home Depot and spray it in the structure.  We did this to make sure we had an exact replica of the interior of the pocket.

Step 5: Once dried, we trimmed and shaped the foam to how we wanted.  This can be done with 36 grit sandpaper and a sharp knife.

Step 6: Once shaped, we used 3M Super trim adhesive again.  Instead of staples, we used the adhesive to keep the fleece in place.  This allowed me to move the fleece where I wanted it and keep it in place, just as staples would.  But it also kept the fleece to the foam, whereas, staples would have shot right though.

Step 7:  Resin and allow to cure.  From here on out, it's just the same as the fronts.  Trim off excess fleece and do body work.

Step 8: Prime and paint.  Reassemble Doors.

MSA's 2013 SEMA Project: Black Rhino > Speaker Pods - Building the Front Speaker Pods Step by step

As I mentioned before, the main challenge here is clearing the dash when the door closes.  We measured this area several times and marked the doors where it would be safe.  We then began building the wooden structure.  To make this a little more challenging, we wanted to see the door panels almost effortlessly move into the speaker pods.  We trimmed the panels so that the pods for the front doors would slide right under the panel.  We then built the wooden structure and made sure all components cleared the doors.  Success!  Then comes the build.  Here's what we did step by step.
Step 1.  I used strand fiberglass to create a base.  I wanted something that was form fitting and sturdy enough for the wooden structure to stick to.  We used aluminum tape and pressed in all the grooves, corners, and made it contour to the exact shape of the door.
Step 2: Wax wax wax.  Resin doesn't like to stick to waxy surfaces, so this allows us to pull the fiberglass away from the door when the mold is complete.

Step 3: 3M Super trim adhesive.  One of the most difficult things to do in this process is making sure the fiberglass itself works through the grooves and the shapes its supposed to, giving it the strength.  We actually use the glue to do this and press the fiberglass where we need it.

Step 4: Resin.  Cover the fiberglass strands in as must resin as possible.  Enough to create a level surface we can adhere the wooden structure to.

Step 5: Let dry.

Step 6:  Once its dried, we were able to pull the fiberglass straight off the doors for a perfect bottom structure for the pods.  The fiberglass is sturdy enough now, I used a nail gun and through the bottom of the fiberglass, shot nails into the wood, holding it in place.

Step 7: Then comes the fleece.  Using staples, we wrapped the wooden structure using fleece, keeping it as tight as possible and forming the generic shape we wanted.  For novices, fleece is used to absorb resin.  It offers some rigidity once absorbed, very much like fiberglass does, so It's popular to use when making "
"fiberglass" enclosures.  When sanding, you don't get all the fiberglass debris in your arms and so it's nicer on the skin as well when sanding.

Step 8: Resin and let dry.

Step 9: Once dried, we cut away any excess fleece and using a roloc disc, shave down any mistakes in forming the fleece.  Sometimes it doesn't stretch exactly where you need it and spots become wrinkled.  That's not an issue.

Step 10: Once done, we take short strand fiberglass filler and fill in any necessary areas.  We also use it to get both structures to match up better.

Step 11: More fiberglass short strand and bondo.  Layer, sand, and shape.  Repeat, repeat, and repeat until the process is done.  Between a few of these steps, you may use primer to get an idea.  It can be sometimes difficult to see if the shapes are matching having multiple colors, so a can of Duplicolor Gray Primer works great.

Step 12: Use higher grit sandpaper and continue to shape.  Your end point will be determined what you're doing.  We are spraying flat black and texturizer, so for our application, it doesn't have to be perfect.  However, if you are doing a gloss paint like on the exterior of a car, you have to continue until all the waves and imperfections are gone.

Step 13: :Paint, cut out the holes for the speakers, mount it to the panels.  What's left is up to your audio expert.  :D